DeWALT DW723 Christmas Sales!
 |
DeWALT DW723 Christmas Sales!.
Product: DeWALT DW723 Amazon Price: Too low to display Availability: In Stock |
Compare Prices on DeWALT DW723
This is a edifying product with some flaws.
The Good:
Very portable and lickety-split and easy to place up.
It is stable (grand more stable than it looks) .
Long adjustable supports.
Flip stops are handy for repetitive cuts.
The tag - quite reasonable when you scrutinize at the competition (or even the previous version of this stand) .
The Bad:
The biggest spot is that the supports are unbiased too slight. Yes you can plot the aid 12' from the blade but there is no back in between. This is a predicament when squaring the ends of 16' mdf moldings - they really sag. Cutting mdf moldings accurate is even worse - a little bend in this scenario results in the molding falling of the front or wait on of the succor.
The supports adjust easily to match the height of your saw. The scrape? Understanding on adjusting them constantly because they will not quit do. Also the beams that the supports sit on have some wiggle room to allow them to pace in and out. At fat extension the beam can be depart as noteworthy as 3/4" up or down
My review is somewhat negative because I wanted potential buyers glance both sides - all the gorgeous reviews conceal some flaws. However, I tranquil really esteem this stand. You can not beat the portability of this stand. The problems I have found have been solved in some other stands but those things are honest astronomical beasts. The portability is far more considerable to me. Also the stiffer your material the better. The stand really shines for rough carpentry - where limited variances with the stops don't matter, the height of the supports can be off a bit, and the material is straight enough to not descend off the assist or sag in between. I have often gash 4 x 12's for headers (as long as 14') and the stand held the up perfectly.
Most of my grievances only arrise when using MDF moldings. The fact that I do so regularly is probably the biggest factor in my 3 star rating.
In case you were wondering - I'm a contractor and I have aged this stand almost every day for about 18 months.
I've have reduce my allotment of board feet while squating in front of my miter saw while it was on the floor. As I pick up older, this was going from being inconvenient, to a exact wound in the wait on. (Literally!) There was no plan to encourage the ends of the board other than shimming with scrap lag prior to each slit. I tried mounting it on top of my B&D Workmate, but supporting the ends of the boards became even more of an enlighten. I knew I wanted a mitersaw stand, but which one?
I liked different features of the different stands I reviewed, like colossal wheels, heavy construction and additional work supports. Some looked like I could copy their form and weld from square tubular steel. Weight would be a consideration. Combine this with the weight of the saw, it could be over 160 pounds. Getting it into and out of my SUV without trashing my bumper (and my assist) would be a trick. Using aluminum rectangular tubing would be lighter, but really pricey! After looking at the others, I decided on the Dewalt 723. I am joyful I did! Most of the others near in kit gain, the 723 is fully assembled. It folds into a compact package, is relatively light, very sturdy, made from high quality components, and it is one of the most professional looking stands around (especially when mounting a matching Dewalt miter saw on it!) .
Most bolts have Allen-wrench heads. Any that are adjusted often (such as the extention arms and supports) have big T-handles. All nuts are the type that have nylon lock-washers to retain from vibrating loose. The saw brackets place (and detach) snappily from the main beam. There are rubber feet attached to the brackets so the saw can be mature alone on a bench (or on the floor...) if desired. The arms will wait on 99.5% of the saunter I will be chopping without sagging. When I want to throw an 8' 4x12 on the stand, it will require supports (2x2s will do) clamped to the arm, extending down to the ground. Other stands have these extra supports already attached, but are unneccessary for the tremendous majority of my cuts; and will only add to the weight and complexity of break-down for transport.
By folding down my rear seat of my SUV, I can accumulate the stand to fit with ease. The saw is aloof, and placed next to it. I will probably establish a pair of 10" phenumatic wheels to one ruin for easier protability around a job spot. I like the table saw extention the Delta folks have on their stand (model 50-155), and will incorprorate a puny extention similar to theirs on the DW723. There are some cheaper stands around, but they were either too heavy (up to 90 lbs for the stand alone!) or too flimsy (for mounting a DW708 12" compound sliding miter saw) . The package arrived in ravishing shape with no wound to the stand.
I highly recommend this stand. Now that I have one, I wonder why I didn't acquire one sooner. I'll never go encourage to squating on the floor again.
Let me say up front that if I owned a DeWalt miter saw, I'd give this stand a perfect 5.
As a previous reviewer brought up, the Makita saw is a bit deeper, and for some reason the rear mounting holes are inset from the front mounting holes. No quandary if you are resourceful, and have a itsy-bitsy angle iron on hand. Being able to adapt additional mounting rails to a variety of tools could do this an extremely versatile tool. Imagine unclipping your miter saw, and dropping on a tablesaw, bandsaw, or sander, with each swap taking less than 30 seconds!
After I fabricated a few mounting rail extensions for my Makita, the saw dropped onto the mounting rail like silk! There's a lot to like about this stand. It is immediately solid, and no hint of being tipsy even when the sawhead on the 12" saw is locked to the rear situation.
I was concerned that the extensions would be too flimsy to encourage a long deck board, but after I leveled the extension to the table (more on this later) it was very solid, and sliding the 2x6x12 encourage & forth as when you are aligning a nick tag, there was very minute deflection or bouncing.
After I initially mounted the saw, I found that the Makita table is higher than the supports will go. I conception to modify a station of my acquire beget to match my saw. DeWalt may have balked at making a more universal despicable, but the fact is there are a LOT of different brands of saws out there and only a handful of quality tables available. Don't know about the substantial boys, but I've never turned up my nose at a potential revenue stream!
In the folded set, the stand is a petite fleshy, especially after hoisting 2x goods all day, but not too abominable. From the time the stand comes off the truck to position up & ready to work, has been as quick as 2 minutes! I don't deem the Trojan can be site up that posthaste, and that table is very tipsy with a 12" saw mounted to the rear of the table.
If you have a DeWalt saw, this stand is a no-brainer. If you have a different imprint of saw, I'd hiss taking the time to execute a plywood defective as instructed by DeWalt to mount your particular saw. This one is tough and ready to go to work accurate out of the box.
Tickled Cutting!
